伊人久久大香线蕉AⅤ色,午夜精品乱人伦小说区 ,色五月丁香五月综合五月亚洲,国产一产区二产区

電泳技術

分享電泳設備設計制造服務及電泳漆技術咨詢

當前位置：首頁 ? » 電泳設備電泳設備工藝 ? 正文

電泳槽液循環簡介中英對照版

1225 人參與 2011年11月08日 05:54 分類 : 電泳設備電泳設備工藝評論

電泳槽液循環簡介中英對照版 The sections of "Design Considerations" on Paint Circulation are considered definitive in their specific information and reasons for recommendations. However, the following operational comments should prove helpful. 在“設計依據” 一節中，就槽液循環有關具體數據及原因方面已提出明確建議。然而，以下的操作說明對操作是有幫助的。 Pump operation, regardless of type, should be monitored by pressure sensors downstream from the pump. Low pressure should sound an alarm which requires positive response. To avoid the problem of pump overheating, pumps should not be dead-headed. 泵的運行（與泵的類型無關）要靠裝在泵出口的壓力傳感器監控，壓力降低時有聲音報警，以進行必要的調整。在系統運行期間，避免泵的過熱問題，泵不應固定不變。 Filters are usually changed when a specific pressure differential reading occurs. This practice can delay the filter change until the filters reach their maximum filtering capacity and reduce unnecessary changes. Many plants have adopted a change schedule determined by experience on a particular line. However, pressure differential should continue to be taken daily as a precaution against a catastrophic event, and pressure gauges should be regularly replaced (again according to a schedule determined by line experience) to assure reasonable accuracy. 當壓差達到一定讀數時，一般要更換過濾介質。這樣過濾介質的更換可以延遲到過濾器達到其最大的過濾容量時再進行，以減少不必要的更換。許多廠家已采用了依據特定涂裝線的經驗制定的更換時間表，然而，壓差讀數要連續地每天讀取，以預防大的事故發生。壓力表要定時更換（這也是依據涂裝線經驗制定的時間表），以確保讀數準確無誤。 All filter changes should be recorded in a log which includes the date, time, and filter size. 所有過濾器的更換都要在值班記錄上做記錄，包括日期，時間，及濾網規格。 Piping should be color-coded and labeled with direction arrows to indicate material in the pipe and direction of flow. 管路要涂顏色標記及帶指示箭頭的標牌，以指示管路內的材料及流動方向。 Critical valves (for drains, D.I. water. etc.) should be locked or valve handles removed to avoid accidental opening. Far too much paint has been wasted because of the accidental opening of valves. This directive is of primary importance! 一些關鍵的閥門（排放閥，去離子水等）要鎖上或取下閥門手柄，以防意外打開，因閥門意外打開時，必將浪費大量涂料，這一點極其重要。 Additions to the tank should be volume-metered to avoid tank overflow. Meters should be checked and calibrated periodically. Physical inventory measurements should be taken at least weekly and compared with metered usage. This practice will provide a check-and-balance system and will help to verify meter operation. These checks are critical, especially when just-in-time and consignment inventory practices are operative. 向槽中添加物料要有容積計量，以防止槽液溢出?？刂苾x表要定期進行檢查和校正，至少每周進行實際用料計量并與儀表計量值做比較。這樣可嚴格控制加料及庫存量，并同時可校驗儀表的精度，這些檢查很關鍵，特別是在要非常準確地控制庫存量的情況下。

本公司可以承接電泳生產線和各類涂裝生產線設計、制造、施工，為您提供一流的涂裝生產線生產制造服務，讓您更省時、省力、省心。