伊人久久大香线蕉AⅤ色,午夜精品乱人伦小说区 ,色五月丁香五月综合五月亚洲,国产一产区二产区

電泳技術

分享電泳設備設計制造服務及電泳漆技術咨詢

當前位置：首頁 ? » 電泳設備電泳設備工藝 ? 正文

電泳電源簡介中英對照版

1165 人參與 2012年02月09日 00:00 分類 : 電泳設備電泳設備工藝評論

Power Supplies-電源：Rectifiers should be capable of voltage adjustment between 0-500 volts. Operating history has shown a power consumption of approximately 2.5 amp hours/100 ft for current electrocoat products. System design should include an allowance for an additional 50% amperage to provide for future developments. Average current requirements for coating a vehicle can be calculated by using this equation: 整流器電壓能使電壓在0-500V之間可調，實踐經驗表明厚膜電泳漆電流消耗大約為2.5安培 .小時/100平方英尺，系統設計要考慮50%的電流余量以供將來發展，可用以下公式計算泳涂一臺車所需總電流。 Amps Required =(2.5 Amp Hrs/100 Ft ) x (Coatable Surface/Minute) x (60 Minutes/Hr) 所需安培數=（2.5安培.小時/100平方英尺）x（能涂的面積/分） x（60分/小時） Multiply the amps required by 1.5 to determine amplifier size to include the safety factor. The total amperage is divided into two zones; several rectifier modules are used in each zone (see Figure 12). Back-up rectifiers should be included in the design with proper switching to assure that production will be uninterrupted and quality undiminished in the event of rectifier failure. Current-limiting rectifiers are recommended for equipment protection. Variable-time, ramped-voltage circuitry is recommended for starting systems occurring after conveyor stops to prevent current surges which can damage coatings. Ramps of 10-15 seconds from 0 voltage to operating voltage have performed well. The rectifiers should be installed so that no power to the system is present when no production is in the tank (during lunch breaks, e.g.). 考慮安全系數，這個安培數乘以1.5來求出放大的規格，把總流量分成兩份，每一部分單獨配整流器（見圖12），設計要考慮配有專用及獨立啟動的備用整流器，以確保即使整流器發生故障時生產也能繼續進行且質量不降低。建議采用限流整流器以保護設備?？紤]停鏈之后工藝槽中有工件在重新啟動，要求有可調時間的漸升電壓電路，這樣的電路可防止電流脈沖損壞涂層繼電器設備，從零伏升到工作電壓的升壓時間以10-15秒較好，要裝有能控制不生產時（如午餐等）不為系統供電的控制器。 The degree of "smoothness of power" or ripple delivered by a rectifier is important. The D.C. power should be filtered such that the magnitude of peak voltages does not exceed 5% of the average D.C. with a voltage ripple of less than 5% under all load conditions. 整流器“供電平穩”度或輸出脈動率很重要，直流電要經濾波，電壓脈沖幅度不超過平均直流電壓的5%，滿負荷情況下，電壓脈動率要小于5%。 Ripple is defined as: 脈動率定義為： 100 x RMS Voltage of the A.C. Wave on the D.C. / the Average D.C. 100 x在直流電壓上的有效交流電壓/平均直流電壓 Grounded power-on entry provides the greatest personal safety, the least complicated switching system, and the longest coating times on lower body areas. It also reduces arcing and pitting of shoes and contact skids. 工件帶接地電壓入槽提供了最大的人身安全性，使開關系統更簡化，且能得到對車身下部最長的電泳時間，同時也能減少電弧放電和燒壞電制，滑架等事故。

本公司可以承接電泳生產線和各類涂裝生產線設計、制造、施工，為您提供一流的涂裝生產線生產制造服務，讓您更省時、省力、省心。